ºñÁî´Ï½º 778

ACO

AMETEK

APPLIED MEMBRANES

AMITTARI

ARCOTEST

BALMAC INC

BECKMAN COULTER

BJORNAX AB

BW TECHNOLOGIES

CHEM INSTRUMENT

DAKOTA ULTRASONICS

DCS INC

DEFELSKO

DIAVITE AG

NIPPON DENSHOKU

ECOPIA

EGG TESTER

ELCONTROL ENERGY

EIT INC

ETS-LINDGREN

FOURIER SYSTEM LTD

FOURTEC

GALLTEC + MELA

GE SENSING

GRANT INSTRUMENTS

HYDRONIX

IET (IDENSHI)

IKM INSTRUTEK

IMV CORPORATION

INSTRUTECH INC

ION SCIENCE

JFE ADVANTECH

KELLER

LIST-MAGNETIK

METONE

MICRONICS LTD

MIKRON

MTI INSTRUMENT INC

NITTOSEIKO ANALYTECH

OKANO WORKS

ONO SOKKI

PCWI

PINION PRODUCTS CORP

RALSTON INSTRUMENTS

RM YOUNG

SCANSENSE

SHAW MOISTURE METER

SHOTOX

SHOWASOKKI CO LTD

SHINYEI KAISNA

STRESSTEL

TESTO

TRAFAG

TREK INC

UE SYSTEM

ULVAC

WILDCO

ZAWADA NDT

OTHER MAKER

 
High Accuracy Flowmeters and Controllers
High Accuracy Flowmeters and Controllers
  ¸ðµ¨¸í : HFM-305 / HFC-307
  ¿ø»êÁö : ¿µ±¹
  Á¦Á¶»ç : CHELL INSTRUMENT
  °¡   °Ý : ¹®ÀÇ
  ºÐ·ù¸í : High Accuracy Flowmeters and Controllers
product
Á¦Ç°»ç¾ç
Àû¿ë»ç·Ê
±â¼úÀÚ·á
 

 

High Accuracy Flowmeters and Controllers

(from 0-1000slpm to 0-3000slpm)

HFM-305 / HFC-307

Features

  • Range - 1000-2500 slm (Air Equivalent); Higher Flows Available
  • ¡¾1.0% of Full-Scale Accuracy
  • Rapid Settling Times: HFM-305 <= 0.4 seconds HFC-307 <= 2.0 seconds
  • Operating Pressures to 500 PSI
  • NIST or UKAS Traceable Calibration
  • NEMA 4 Enclosures Available

Applications

  • Gas Blending
  • Research
  • R&D and Process Flows
  • Pollution Monitoring

Hastings Instruments products represent over 50 years of experience in the design and manufacture of mass flow products. The 300 Series is a culmination of this experience with patented technologies that make these the finest flowmeters and controllers available today.

The Hastings Mass Flow 300 Series products are designed to accurately measure mass flow without corrections or compensations for gas pressure and temperature. They are accurate to better than ¡¾1.0% of full scale. Hastings mass flow instruments do not require any periodic maintenance under normal operating conditions with clean gases. No damage will occur from the use of moderate overpressures (~500 psi) or overflows. Instruments are normally calibrated with the appropriate standard calibration gas (air), then a correction factor is used to adjust the output for the intended gas. Special calibrations for other gases, such as oxygen, helium and argon, are available upon special order.

For applications where combustible gases are metered, this model is available in a NEMA 4 housing. Integral seals make for safe handling of gases, including helium and hydrogen, where separate enclosures were once required. Product bulletin PB156, which will be published early 2001, contains these details.

The 300 Series products contain a number of features that set them apart from other available instruments: (1) They are inherently linear; no linearisation circuitry is employed. Should recalibration in the field be desired (a calibration standard is required), the customer needs to simply set the zero and span points.